Leading 10 common forklift crashes ， forklift operation must take note of these issues ！.

Leading 10 common forklift crashes ， forklift operation must take note of these issues ！.

Blog Article

Don't underestimate the forklift at the office. If the procedure is bad, there will certainly be significant crashes in mins, and there are several accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a moving crash.
Instance 2: In order to keep the balance of the forklift when raising hefty items, the staff members utilized their body weight as the counterweight, which practically triggered casualties.
Case 3: The width of the forklift freight goes beyond the permitted width of the route and hangs on the roadside rack, which nearly triggers an mishap.
Case 4: Forklift is speeding and surrender during a turn.
Case 5: The forklift driver did not notice the pedestrian, and the pedestrian did not see the forklift.
Instance 6: The forklift lifts the personnel unlawfully, the forklift motorist does not wear the seat belt, the forklift lifter falls and the chauffeur is crushed when the forklift surrender.
Instance 7: The forklift motorist did not wear a safety belt and dropped from the lorry when it surrendered and was crushed.
Forklift procedure ought to pay attention to these issues ：.

Begin.
1. Before beginning, observe the environments, and after confirming that there are no obstacles that impede the security of driving, honk the horn initially and after that begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before beginning.
3. When the forklift begins with a load, the vehicle driver must first confirm that the lots is steady and reputable.
4. The beginning must be sluggish and steady.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be kept at 300mm-400mm, and the pole needs to be slanted backwards. .
2. Do not raise the fork expensive when driving. When getting in and leaving the work site or while driving, beware that there will be no challenges overhead. When the tons is traveling, the fork must not be increased expensive, which will certainly affect the stability of the forklift. .
3. After unloading, the fork should be reduced to the regular driving setting prior to driving. .
4. When transforming, if there are pedestrians or automobiles close by, the driving signal should be provided initially. High-speed sharp turns are prohibited. High-speed sharp turns will certainly cause the vehicle to lose lateral security and topple. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is restricted to brake unexpectedly while driving with loads unless there are special circumstances.
6. When the forklift is running, it needs to follow the web traffic rules in the manufacturing facility and should maintain a particular safety distance from the car ahead. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry should be effectively tilted back. The tons will not be elevated other than when piling or loading. .
8. The height of the lots must not obstruct the chauffeur's sight. In special situations, when the product influences the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to turn on the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the factory location is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop area. .
11. When the forklift is raised, lifted or driven, it is forbidden for personnel to depend on the fork to hold things and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a timely manner, and they will certainly never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the range between the two forks ought to be adjusted as required to make the tons of the two forks balanced and not skewed, and one side of the item need to be against the shelf. .
2. It is forbidden to work with a single fork or utilize a fork top or pull. In special circumstances, safety indication should be established to remind surrounding pedestrians. .
3. In the process of filling and discharging items, the forklift must be braked with the brake. .
4. The speed of the automobile should be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as feasible under the load, and it should be kept in mind that the fork tip must not touch various other products or objects. The load ought to be maintained with minimal back tilt of the gantry to make sure that the load does not move backwards. The pole can be slanted forward somewhat when the lots is lowered to permit simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork goods at broadband and collide with difficult items with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Straining is restricted, and it is forbidden to use forks to lift employees to participate in high-altitude procedures to stay clear of high-altitude falling accidents. .
9. It is not enabled to make use of the brake inertia to slip, place, round or roll items. .
10. It is not permitted to make use of forks to pick, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you should discharge the goods or reduced the fork framework.
2. Draw the parking brake manage to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the driver does not leave the automobile's view and does not exceed 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the look must be examined, and gas, lubricating oil and air conditioning water must be included.
2. Examine the safety and security performance of beginning, running and stopping.
3. Inspect whether Electric Forklift Truck for Warehouse the lights and horn signals are complete and reliable.
4. During the operation of the forklift, examine whether the stress and temperature level are typical.
5. After the forklift is running, the outside leakage ought to likewise be examined and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You need Electric Forklift Truck for Warehouse to inspect before leaving the auto;.
2. When you run into somebody in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming need to not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow and consistent, and no turning on the slope is permitted.
7. Do not drive across the gradient. When the slope is higher than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move forward, if they run into large or heavy goods and most likely to the chauffeur's view, they must take the turning around workout
.
The "Eight Prohibitions" should be adhered to in the procedure.
1. Solitary fork procedure is not enabled.
2. It is not allowed to raise the goods for cross country driving.
3. It is not enabled to grab the goods by handing over the pallet with the fork.
4. It is not enabled to directly shovel chemicals, flammables and other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to get the goods.
6. It is not allowed to use braking pressure to expatriation round or easy-to-roll items.
7. It is not enabled to bring people to work on the pallet or fork, and it is strictly restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following problems.
1. Curves, slim roads, railway crossings;.
2. Sections with a longitudinal incline greater than 5%.
3. When there is an barrier on one side of the roadway, the opposite side of the section with the exact same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844